Nutech AC Metal Primer 15L - Fisher Group

Nutech AC Metal Primer 15L

Metal Primer is anti-corrosive and suitable for new and weathered galvanised and metal sheeting, included coated sheeted roofs.

$184.76

In stock

Categories: ,
  • Next day delivery
  • Top quality products
  • Money back guarantee

Anti-Corrosion Water-Based primer for metal surfaces

Metal Primer is a water-based acrylic primer which exhibits exceptional adhesion and protection to a range of metal surfaces such as:

  • New and old galvanised metal
  • Pre-coated zinc steel sheeting
  • Coated metal sheet roofing
  • Facade cladding
  • Fencing

Surfaces coated with Metal Primer must be overcoated with a Nutech exterior durable water-based coating.

Benefits

  • Improved hardness and flexibility
  • Excellent long term resistance to corrosion and rust
  • Easy application and clean up
  • Suitable for new and weathered galvanised and zinc metal sheeting
  • Weatherproof
  • Excellent adhesion to a wide range of metal substrates
  • Outstanding durability

Suitable Surfaces

Properties

Water Based
Anti Corrosion
Metal Primer
Primer

DOWNLOAD CARE & MAINTENANCE BROCHURE

Download Technical Data Sheet

Download Safety Data Sheet

Weight20 kg
Dimensions31 × 31 × 60 cm
Appearance

Grey viscous liquid

pH

8.5 – 9.0

Solubility

Water

Film Forming Temperature

15°C

Dry Film Thickness

70 microns

Coats Required

1

Touch Dry

30 Minutes

Full Cure

2 hours

VOC Levels

<5%

Flammability

Non-flammable

Ambient Application Temperature

10°C – 30°C

Coverage Rate

5 – 6 sqm/coat

Application Guide

Sealing New Exposed Aggregate Surfaces
Etch uncoated surface with Nu-EcoSafe Etch or Nu-EcoSafe Ultra Etch as outlined in the relevant TDS.
Observe ambient application Conditions noted in the TDS.
Ensure that the surface is clean and dry.
If the surface is affected by white efflorescence, broom over with clean PaveCoat Thinners to dissolve and dissipate all salts before sealing.

Stir thoroughly prior to use.
• 1st Coat: Dilute Agreseal up to 50% PaveCoat Thinners
Apply 1 even coat using a soft bristle broom, roller or spray at the rate of 3 – 5m2/L.
Note: Avoid ponding or pooling. Light mist spray or roller application technique will not ensure adequate surface penetration or long term coating performance.
• 2nd Coat: Apply without solvent dilution in the same manner as the first coat.
If inadequate seal thickness is applied on new exposed aggregate, some efflorescence (salt whitening) may occur. This white powder can usually be washed off easily and should cease after several months.
The application of one or two additional coats of Agreseal can prevent the appearance of efflorescence or white salts.

Sealing & Resealing Existing Exposed Aggregate
Prior to commencement: Determine whether the existing Aggregate has been previously sealed. To determine an existing coating: Refer Nutech Coating Test Kit for detailed instructions or contact Nutech Paint.
Very old, incompatible, delaminating, problem sealers:
• These types of coatings or sealers should be completely removed. Stripping with Nu-EcoSafe Strip Industrial (refer to the relevant TDS) is recommended, to remove all of the existing coatings.
• After coating removal, refer to the un-coated existing exposed aggregate recommendations

Compatible, previously sealed surfaces
This surface will require reactivation to improve intercoat adhesion between compatible sealers.
Prior to reactivation, the existing exposed aggregate surface should be and free from lichen, moss, oil and other debris.
Refer to Nu-EcoSafe Moss Rid and/ or Nu-EcoSafe Degreaser TDS for further recommendations.
NOTE: in order to reactivate an existing compatible sealer, the use of Reactivating Solvent will aid in improving adhesion to the existing sealer.
A test patch should be performed and assessed prior to sealing. Should the test patch fail, removal of the old sealer, acid etching, and high-pressure water cleaning will be required prior to applyingAgreseal.

Un-coated existing exposed aggregate
Thoroughly clean using Nu-EcoSafe Degreaser. Refer to the relevant TDS for further recommendations.
Etch uncoated surface with Nu-EcoSafe Etch or Nu-EcoSafe Ultra Etch as outlined in the relevant TDS.
• Apply 1 even coat using a soft bristle broom, roller or spray at the rate of 3 – 5m2/L.
Note: Avoid ponding or pooling. Light mist spray or roller application technique will not ensure adequate surface penetration or long term coating performance.
• 2nd Coat: Apply without solvent dilution in the same manner as the first coat.